Rent a Skytrak or JLG Telehandler Forklift, 10,000 lb, 54' Reach

Delivery from $140.00 · if machine is available

Delivery + pickup included. Equipment, capacity and timing confirmed at booking.

Delivery rules & ratesNeed it sooner? Give us a call

Rent a Skytrak or JLG Telehandler Forklift, 10,000 lb, 54' Reach

TELH10

Rental Item Details

10,000lb All Terrain Telehandler 54'	Model 10054 Skytrak
Maximum Lift Height	54'
Horizontal Reach	39'
Fork Length Options	4', 5', 6', Long. Also 10' ext.
Carriage Options Fixed, Tilt, Swing	4', 5', 6' Wide
Operating Weight	30,000 lbs
Foam Filled Tires	Standard
Dimensions L W H	20', 8'-6, 8'-6
Diesel	110 HP
DELIVERY ESTIMATE	GET RATE

Manuals

Spec Sheet Skytrak 10054 Telahandler

User Manual Skytrak 10054 Telahandler

JLG 1055 Spec Sheet New 2018 etc

JLG 1055 Operator Manualt New 2018 etc

Skytrak 10054. JLG 1055 Ask about our 2 week rate****

With a boom height of 54 to 55 feet and a 10,000lb lifting capacity, this extremely heavy duty material telehandler will get the toughest lifting jobs done right. With a 4 speed forward and 3 speed reverse modulated transmission, this 10,000lb machine can travel up to 20 mph. The boom takes approximately 15 seconds to do each of the following functions: extend, retract, elevate, and lower. The outriggers must be down to extend boom higher than 42'. The outriggers are 12.5' wide when lowered to the ground. Also known as a Pettibone, Lull, Telehandler, JCB, Gradall, construction Petebone, petty bone or pettybone or lull tell handler or all terrain material handling skytrack or telescopic heavy duty petibone or large tellehandler or telehanler or large pettebon or off road pettebone or 10k Telahandler or Tellahandler or 10k peddybone or a forklift crane or all terrain forklift or Extreme or Xtreme or material handler or rough terrain off road forklift.

FAQ

When should I rent a 10,000 lb / 54' telehandler instead of a smaller forklift or crane?

This telehandler is commonly used for: landing palletized masonry block onto four-story scaffolding; placing pre-assembled roof trusses on multi-story commercial buildings; staging framing lumber packages across muddy or unimproved ground; and unloading steel beams or heavy equipment from flatbed trailers. Choose this machine when you need both 54-foot vertical elevation and heavy 10,000 lb capacity on rough terrain. For lower single-story framing under 35 feet or lighter pallet handling under 6,000 lbs, a smaller telehandler will maneuver much faster in confined jobsite footprints. If you are looking for high reach and suspended weight, and excellent alternative is the <a href="https://www.gappower.com/products/magni-rotating-telehandler-98-13-000-lbs-roto-boom-telhro98">Magni Rotating Telehandler 98' 13,000 lbs Roto Boom</a> .

Do I need to deploy the outriggers to use the boom?

Yes, outriggers must be lowered to the ground whenever elevating the boom higher than 42 feet or handling loads that require stabilized chart ratings. When deployed, the outriggers span 12.5 feet wide. Ensure your staging area has adequate lateral space and firm, compacted ground to support the outrigger pads before lifting.

Can this telehandler lift its full 10,000 lb capacity at maximum height or horizontal reach?

No, maximum capacity ratings apply only when the boom is retracted and at steep lift angles close to the front of the machine. As you telescope outward toward the 39-foot maximum horizontal reach or up to 54 feet, allowable payload decreases substantially. Always check the in-cab load chart corresponding to your specific boom angle and outrigger position before picking up a load.

How is this telehandler transported to my jobsite?

With an operating weight of roughly 30,000 lbs and dimensions of 20 feet long by 8.5 feet wide, this machine cannot be hauled on standard equipment trailers and requires commercial semi-truck lowboy transport. Gap Power also offers jobsite delivery, make sure to verify that your delivery location has wide, clear access roads and adequate turning radius for a tractor-trailer.

What fork and carriage options are available for this unit?

Gap Power offers a variety of attachments including, a carriage, concrete hopper, and work platform. Each rental comes equipped with standard forks at no charge. Standard fork tines are available in 4-foot, 5-foot, and 6-foot lengths, along with 10-foot fork extensions for bulky materials. Carriage options include fixed, tilt, and swing carriages in 4-foot, 5-foot, or 6-foot widths to simplify placing loads onto unlevel surfaces or through narrow framing bays.